Logic Corp. Injection Molding Equipment. LogicSeal Cond Specs

LS-400

NO LEAKS ABSOLUTELY GUARANTEED – The Logic Corporation can safely make that statement. The Logic Seal works below atmospheric pressure; air pressure outside the mold is always greater that the pressure in the mold’s water channels. The outside pressure will always force the coolant to flow in its channels. A leak is tamed before it can start.

With the Logic Seal^tm leakstopper, faulty '0' rings and cracks in the mold no longer mean an interruption in production: you just keep right on molding! Often, you can even achieve faster cycles due to improved coolant flow.

The advantages don't stop there, however. As the owner of genuine Logic Corp. equipment, you may also be licensed, free of charge, to use any one of our exclusive, patented processes to decrease cycle time in truly dramatic fashion. These include Water Transfer^tm and Waterline Venting^tm. There are even many, many more techniques possible only with negative pressure technology. Logic Corp. offers free consultation to their customers in using any of these procedures. Talk to the professionals ... talk to Logic Corp.

SPECIFICATIONS for LOGIC SEAL & MERLIN
	LS-300*	LS-400	LS-500	LS-100*	LS-350
MOTOR	0.75	1.50	2.00	0.75	1.50	HP
MAXIMUM FLOW	15.0	24.00	53.2	4.7	14.80	G.P.M.
MAX RETURN PRESSURE w/ 10 P.S.I. Neg	40.00 2.81	40.00 2.81	40.00 2.81	90.00 7.03	140.00 10.55	P.S.I. KG/CM²
PORTS Supply & Return	0.75	1.25	1.25	0.75	0.75	N.P.T. (FEMALE)

* Available in single phase

HOW TO SIZE UP A LOGIC SEAL TO A MOLD

Please call 800-325-6442 to discuss your requirements or if you prefer, you can fill out the following & Fax it back to us at 866-395-1457.

A representative will get back to you with the unit best suited for your application.

Guaranteed to stop the leak.

1. Supply Pressure:___________________

2. Drain Pressure:___________________

3. G.P.M. required to the circuit the unit will operate:___________G.P.M.

4. If you do not know the G.P.M.

Give the following:

a. Dia. of cooling line into the mold circuit:_________Inches

b. Number of circuits _________

5. What phase do you prefer?

a. Single Phase 1) 110 volts 2) 240 volts

b. Three Phase 1) 240 volts 2) 480 volts ________ Phase

Voltage: ________ Volts

6. Would you like temperature control of this circuit? Yes____ No____

Customer information:

Company:_____________________________ Date:____________________

Address:_______________________________________________________

Contact Name:____________________ Phone:______________________

E-mail:___________________________ Fax:_________________________

With a 4.7 gpm (max) positive displacement pump, circuit breaker on incoming power, motor starter relay, Thermal overload protection on motor, 110 volts (8 Amps)/240 volts (4 Amps)50/60 Cycle, UL/CE Rated, Safety shut off switch for Low Supply pressure with indicator light, vented steel cabinet, bonded rubber casters, liquid filled compound gauges on TO MOLD and FROM MOLD lines, liquid filled SUPPLY and RETURN pressure gauges, adjustable bronze pressure regulating valve, bronze inline filter, adjustable flow control circuit to minimize part wear, copper and bronze plumbing, max. drain (return) pressure capability is 100 psi. All ports are 3/4" NPT (TO MOLD, FROM MOLD, SUPPLY & DRAIN (Return)

With a 4.7 gpm (max) positive displacement pump, circuit breaker on incoming power, motor starter relay (120 volt control circuit), Thermal and electronic overload protection on motor, pump reversal protection with indicator light (Phase Monitor), 208-240 volts (3 Amps)/ 380-415 volts (1.8 Amps)/ 440-480 volts (1.5 Amps)50/60 Cycle, UL/CE Rated, Safety shut off switch for Low Supply pressure with indicator light, vented steel cabinet, bonded rubber casters, liquid filled compound gauges on TO MOLD and FROM MOLD lines, liquid filled SUPPLY and RETURN pressure gauges, adjustable bronze pressure regulating valve, bronze inline filter, adjustable flow control circuit to minimize part wear, copper and bronze plumbing, max. drain (return) pressure capability is 100 psi. All ports are 3/4" NPT (TO MOLD, FROM MOLD, SUPPLY & DRAIN (Return)

With a 14.6 gpm (max) positive displacement pump, circuit breaker on incoming power, motor starter relay, Thermal overload protection on motor, 110 volts (8 Amps)/ 240 volts (4 Amps)50/60 Cycle, UL/CE Rated, Safety shut off switches for Low Supply & High Drain (return) pressures with indicator lights, vented steel cabinet, bonded rubber casters, liquid filled compound gauges on TO MOLD and FROM MOLD lines, liquid filled SUPPLY and RETURN pressure gauges, adjustable bronze pressure regulating valve, bronze inline filter, adjustable flow control circuit to minimize part wear, copper and bronze plumbing, max. drain (return) pressure capability is 40 psi. All ports are 3/4" NPT (TO MOLD, FROM MOLD, SUPPLY & DRAIN (Return)

With a 14.6 gpm (max) positive displacement pump, circuit breaker on incoming power, motor starter relay (120 volt control circuit), Thermal and electronic overload protection on motor, pump reversal protection with indicator light (Phase Monitor), 208-240 volts (3 Amps)/ 380-415 volts (1.8 Amps)/ 440-480 volts (1.5 Amps)50/60 Cycle, UL/CE Rated, Safety shut off switches for Low Supply & High Drain (return) pressures with indicator lights, vented steel cabinet, bonded rubber casters, liquid filled compound gauges on TO MOLD and FROM MOLD lines, liquid filled SUPPLY and RETURN pressure gauges, adjustable bronze pressure regulating valve, bronze inline filter, adjustable flow control circuit to minimize part wear, copper and bronze plumbing, max. drain (return) pressure capability is 40 psi. All ports are 3/4" NPT (TO MOLD, FROM MOLD, SUPPLY & DRAIN (Return)