Logic Corp. Injection Molding Equipment. Vac-U-Temp Cond Specs


		VT-2600

PROVIDES MOLDERS WITH DESIGN FLEXIBILITY AND FASTER CYCLES

Takes advantage of negative pressure (whether using water, ethylene glycol, or hot oil). Hot oil under negative pressure - up to 300 degrees. Little or no pressure in your cooling line minimizes dangerous burns from hot oil. Capable of controlling mold temperature + or - 1 degree Fahrenheit.

SPECIFICATIONS

	VT-1800	VT-2600	VT-3000	Unit of Measure
POWER	.75	1.5	1.5	HP
MAXIMUM FLOW	22.0	50.0	50.0	GPM
HEATERS	6	6	6	KW
MAX. TEMP.	180.0	260.0	300.0	F
	82.2	126.7	148.9	C
FLUID	WATER	WATER/ GLYCOL	HEAT TRANSFER FLUID

Electrical requirement: 208-240 380, 440-480 volt. 3 phase 60 hertz. With 120 volt control circuit.

All units include the following:

Heavy duty ventilated steel cabinet / bonded rubber casters / easy access to operating controls / complete with vacuum transducers, vacuum adjustment switches and gauges TO MOLD, FROM MOLD, Cooling and Air Supply gauges / copper and bronze plumbing / approx. 5 U.S. gallon stainless steel reservoir vessel / automatic fill control / air separation and removal system / Heat Exchanger / low watt density heaters / fused incoming power

OPTIONS:	Mold purge valve	Remove all fluids from mold and hoses before hoses are removed
	Safety vacuum switch	Activates switch if unit falls below vacuum set-point
	Positive pressure port	Allows running positive and negative pressure simultaneously
	Water transfer package	Allows cooling to flow across the parting line
	Additional heaters	Increase heating capability

A closed-loop, negative pressure system, 50 gpm capability. 1.5 hp motor. Digital dual readout temperature controller. Easy access to operating controls. Circuit breaker on incoming power, motor starter relay (120 volt control circuit), Electronic Overload Protection on motor, pump reversal protection with indicator light (Phase Monitor), 208-240 volts /13.2 Amps or 440-480 volts /8.2 Amps. 50/60 Cycle, UL/CE Rated, Complete with vacuum transducers and vacuum switch (Unit is equipped with a "Pre-Vac" switch to allow the system to be placed under a vacuum and prevent unwanted pressure to the mold before start-up. "Pre-Vac" is also used for first time reservoir fill so that the correct amount of fluid is available at start-up.) TO MOLD, FROM MOLD, COOLING SUPPLY and AIR SUPPLY liquid filled gauges. Copper and bronze plumbing, 5.27(approx) U.S. gallon stainless steel reservoir vessel with automatic filling. Logic�s Air Separation and Removal System with indicator lights. Equipped with a 3.2 square foot Heat Exchanger. 6 Kw low watt density heaters for a maximum temperature of 260 degrees F, using pure industrial ethylene glycol under negative or positive pressure, 210 degrees F using water under positive pressure, or 180 degrees F using water under negative pressure. (Max Temperature will vary depending on pressure using water.) Heavy duty ventilated steel cabinet, bonded rubber casters.

PORT SIZES: (all female NPT) 1-1/4" TO MOLD & FROM MOLD
3/4" Coolant Supply, Return, Air Inlet, & Reservoir Supply.

VT OPT-2H (VT-2600 & 3000)
Additional Heater: Double the KW output by number of heaters used

VT OPT-3
Air Mold Purge Valve: Used to remove all fluids from mold and hoses before the hoses are removed.
Saves time and money by reducing fluid loss.

VT OPT-HE
Larger Heat Exchanger available.

VT OPT-10
Mold Circuit Flow Meter with Digital display

VT OPT-36- 1800 (VT-1800 only)
Separate Fill Port - separates fill & cooling fluid, allowing use of HTF, EG or distilled water

Some options listed reference a specific model number, although they might also be used in another model number.